Introduction

This article presents a brief review on micro machined accelerometers. Different device structures and designs are discussed alongside with their specification and principle of operation. Also a simple design of a single axis accelerometer tutorial is presented.

Accelerometers

Fig.1: Three axis linear accelerometer from ST

The application of micro-accelerometers covers a wide range of fields due to their small size, high performance and low cost. This clearly confirms its second largest sensor market share after pressure sensors. Micro-accelerometers are commonly used tool in automotive, biomedical, industrial, military and numerous consumer applications since it is crucial for safety, measurement and control. Micro-machined gyroscopes (for rate or angle of rotation measurement) are also an emerging technology and it is paving its path into commercialisation as a small companion device with accelerometer. It is becoming an important tool for automotive and different other applications for the low cost, small size compared to conventional gyroscopes. Both micro-accelerometers and micro-gyroscopes are a type of micro-machined inertial sensors.

Micro-machined Accelerometers:

Structure, Specification and Operation:

Fig.2: Mechanical model of an accelerometer

The general structure of an accelerometer consists of a proof mass suspended by compliant beams anchored to a fixed frame. This structure can be modelled by means of a second order mass-dumper-spring system Fig. 2. The fixed frame displacement relative to proof-mass is sensitive to external acceleration which in turn changes the internal stress in the suspension spring. These two values can be used to measure the external acceleration using the Newton’s second law and the accelerometer model to obtain the mechanical transfer function:

$H(s)=\frac{x(s)}{a(s)}=\frac{1}{s^2+\frac{D}{M}s+\frac{K}{M}}=\frac{1}{s^2+\frac{\omega_n}{Q}s+\omega_n^2}$

Where:
a is the external acceleration and x is the proof mass displacement
M : is the proof mass
D : is the dumping factor
K : is the spring constant
$\omega_n=\sqrt{K/M}$ : is the natural resonant frequency
$Q=\sqrt{KM}/D$ :is the quality factor
At a static state (s = 0) the sensitivity of the accelerometer is:
$\frac{x_static}{a}=\frac{M}{K}=\frac{1}{\omega^2_n}$

The total noise equivalent acceleration due to Brownian motion of mass proof suspensions or gas molecules surrounding it is:

$TNEA=\frac{\sqrt{4k_BTD}}{M}=\sqrt{\frac{4k_bT\omega_n}{QM}}$

The final micro-machined accelerometer design can be simulated and optimized using commercially available finite element method or dedicated MEMS software packages. The specification of micro-accelerometer is concerned with its sensitivity, frequency range, off-axis sensitivity and other application specific parameters.

Classification for Micro-machined Accelerometers:

The classification of accelerometers is based on transduction mechanisms, the most useful ones are:

Piezoresistive Accelerometers

A silicon piezoresistor is generally placed at the edge of the rim and proof mass where stress variation is maximum. This causes change in the resistivity as the beam changes its mechanical state. The structure, fabrication process and circuitry of these devices are simple. However, they have a larger temperature sensitivity and smaller overall sensitivity which drops its accuracy.

Capacitive Accelerometers:

This is based on the gap variation between the proof mass and a fixed electrode which in turn changes the capacity. The capacitive based accelerometers are preferred for several reasons: simple structure, high performance, low cost, low power dissipations, high sensitivity and low temperature sensitivity. Although it is susceptible to electromagnetic interference, good packaging and shielding prove to be the solution.

Tunnelling Accelerometers:

This type of devices uses a constant tunnelling current between a tip attached to a movable microstructure and its counter electrode to sense the displacement. The tunnelling current is maintained constant as long as the distance and tunnelling voltage are unchanged. Once the proof mass moves due to acceleration, the circuit responds by adjusting the deflection voltage to bring the tip back to its place. Measurement of deflection voltage in this closed loop system can be used to calculate acceleration. Its drawback is that it is sensitive to low frequency noise.

Resonant Accelerometers

This is based on transferring proof mass inertial force to axial force on the resonant beams and hence shifting its frequency. The output is digital and highly sensitive.

Thermal Accelerometers:

The temperature flux between a heater and heat sink is proportional to the inverse of their separation; hence by measuring the temperature, the displacement can be also measured.

Other Accelerometers:

In addition to the above mentioned accelerometers types, there are other devices based on optical, electromagnetic and piezoelectric principles. The reason behind is to use advantages of both micro-machined and physical principle like optics are immune to noise and linear.

How to design an Accelerometer?

The main steps to design a simple single-axis capacitive accelerometer bulk micromachined are covered in this tutorial.

The required parameters to take in consideration in order to design an accelerometer are:

The Bandwidth (###) Hz,

The Sensitivity (#. #) pF/G,

The Dynamic range +/- (##) G,

The Minimum detectable acceleration (#) mG.

Mechanical study

Design approach

Fig.3.1: Single axis accelerometer

The aimed design to be fabricate is a single -axis capacitive accelerometer (See Fig. 3.1), this system contains:

a mass (m),

a spring (with constant k),

and a dumper (with coefficient b).

This system can be translated to a simple mechanical system as it can be seen in Fig.3.2:

Fig.3.2: The Behaviour of an accelerometer

This system is just an approximation to the real approach behaviour. This mechanical system gives a second order system given by:

$m\frac{\partial^2x}{\partial t}+b\frac{\partial x}{\partial t}+kx=F_{ext} = ma$

dividing by m, thus:

$\frac{\partial^2x}{\partial t}+\frac{\omega_n}{Q}\frac{\partial x}{\partial t}+\omega^2_n=a$

witch gives a transfer function (Lapalce domain):

$\frac{x(s)}{a(s)}=\frac{1}{s^2+\frac{b}{m}s+\frac{k}{m}}$ or $\frac{x(s)}{a(s)}= \frac{1}{s^2+\frac{\omega_n}{Q}s+\omega_n^2}$

where:
$\omega_n=\sqrt{\frac{k}{m}}$ : is the resonant frequency, and
$Q=\frac{\omega_nm}{b}$ : is the quality factor.

the rest is coming soon .

Assumption and limitation

The basic limitation are needed to look at :
……………..
The critical damping, this permits to get the least amplitude distortion. This means that therefore [3]:
…………..

Dumping characteristics

Geometries

Electrical & Electronics studies:

Electrical model of the accelerometer

Block diagram for open loop

Fabrication process of a bulk micromachined accelerometer:

Microfabrication process of the mass and beams of the acceletometer

References

[1]
[2] Michael Kraft, Notes, university of Southampton 2004.
[3] Senol Mutlu, Surface Micromachined Capacitive Accelerometer With Closed-Loop Feedback
[4] N. Malauf. An Introduction to Microelectronical System Engineerin. Aretech House. 2000.
[5] Kovacos, micromachined Transducers Sourcebook
[6] Beißner, S.1; Puppich, M.2; Bütefisch, Analog Force Feedback Circuit for Capacitive Micromechanical Acceleration Sensors.
[8] M. C. Wu.Case Study I: Capacitive Accelerometers. Chapter 19 of S. Senturia, Microsystem Design.
[9] Michael Kraft’s Thesis, http://www.ecs.soton.ac.uk/~mk1/. 13.05.2004
[10] Joseph I. Seeger and Bernhard E. DYNAMICS AND CONTROL OF PARALLEL-PLATE ACTUATORS BEYOND THE ELECTROSTATIC INSTABILITY. Sendai, Japan, June 7-9, 1999, pp. 474-477

Share and Enjoy: These icons link to social bookmarking sites where readers can share and discover new web pages.